Home > ELECTRICAL > ROUGH ELECTRICAL > ELECTRICAL FITTINGS
Sort By:
1 2 3 ... 20
Eritech ZWP1J Grounding Pipe Clamp Erico CC58 Threadless Compression Coupler 2-1/2IN DIECAST LOCKNUT
Bolted water pipe clamps made of zinc die-cast. Wire range 8 sol. - 2 str. UL Listed. Connects grounding wire to the grounding rod. Use when compression couplers are required around ground rod splices. Enable ground rods to be driven deep quickly and easily without the risk of rod separation. Manufactured of high-strength silicon bronze. Coupling is tapered, so when the rod is driven into the coupling the two parts compress to form a conductive connection. Use to secure Rigid or IMC conduit or various threaded fittings to a steel outlet box or other metal enclosure. Bulk packed.
Carlon UA9AHB-CTN Standard Radius Rigid Conduit Elbow 3/4IN BOX SPACER 1/2 RIGID BOX SPACER
For use with nonmetallic solvent weld fittings. Nonconductive, impact, corrosion and sunlight resistant. Schedule 40. UL 651 Listed to the NEC by the ETL, UL Listed. Zinc die cast. Use as a raceway between two steel outlet boxes or other metal enclosures. UL Listed. Bulk packed. Zinc die cast. Use as a raceway between two steel outlet boxes or other metal enclosures. UL Listed. Bulk packed.
3/4" EMT SET SCREW CONNECTOR Halex 61215B 2-Hole Conduit Strap Carlon A240D-CAR 1-Piece Conduit Coupling
Zinc die cast. Use to connect EMT conduit to steel outlet box, load center or other metal enclosure. UL Approved. Indoor or outdoor use. Use to secure Rigid or IMC conduit to wood, masonry or similar surfaces where greater load bearing is required. UL Listed, CSA Approved. Quick connect, fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed.
Carlon A240E-CAR 1-Piece Conduit Coupling 1/2 RGD&IMC BOX SPACER ZINC 1-1/4 FLEX-BX SQUEEZE CONN
Quick connect, fold and snap together. No cement, set screws or lock nuts. For 600 volt use in ceilings, floors and walls in residential, commercial and industrial buildings not more than three floors above grade. Colored in brilliant electric blue. For indoor use. Concrete tight when used with Carlon ENT. UL Listed. Die cast of high strength corrosion resistant zinc alloy. Locknut is reversible. It is designed to cut through protective coatings on boxes and enclosures to assure ground continuity. Use as a raceway between two steel outlet boxes or other metal enclosur Zinc die cast. In a dry location, use to connect flexible metallic conduit (Greenfield or BX) to steel outlet box, load center or other metal enclosure. Fits 1/2" knock outs. UL Approved.
1IN PLAST INSULATING BUSHING Halex 61107B 1-Hole Conduit Strap Carlon A243E-CAR 1-Piece Snap-In Conduit Adapter
High impact thermoplastic. Flame retardant to 105 degrees C. Use with locknut to terminate threaded Rigid or IMC conduit to an outlet box. The rounded surface of the bushing prevents damage to wire insulation. Required by the NEC. UL Listed, CSA Approved. Indoor or outdoor applications. Use to secure Rigid or I.M.C. conduit to wood, masonry or similar surfaces. Innovative one piece quick connect design for fast and easy installation. Suitable for damp locations. No glue or cement needed. Carlon Standard Blue. Concrete tight when used with appropriate ENT.
1-12 NM/SE CLAMP CONNECTOR 2IN NM/SE CLAMP CONNECTOR 3/4IN 90DEG LIQUIDTIGHT CONN
Fits non metallic cable, flex cords, multi flex cords; fitting range .834 - 1.520 inches diameter SE cables 2 conductor 4/0. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. U Fits non metallic cable, flex cords, multi flex cords fitting range 1.085 - 1.520 inches diameter. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Listed, meets CSA requir Indoors or outdoors. multi-piece. Use to connect flexible metallic or type B non-metallic liquid-tight conduit to a steel outlet box or other metal enclosure or hub.
Halex 26152 1-Hole Snap-On Conduit Strap Halex 36010 Ground Clamp 3/4IN RGD PULL ELBOW W/GASKET
Indoor or outdoor applications. To support EMT conduit. Indoor or outdoor applications. Use to secure the grounding wire to a 1/2" through 1" pipe. UL Listed. Wire size fits #10 - #2 AWG. Zinc die cast. Indoors or outdoors. Use as a wire pulling elbow to facilitate wire pulling through a sharp bend in a run of threaded Rigid or IMC conduit. Removable cover provides easy access to wiring. UL Approved. Bulk packed.
Cutler-Hammer GBK14P Ground Bar Kits Carlon E987H-CAR Rigid Conduit Body Carlon Carflex LN43FA-CAR 1-Piece Straight Conduit Connector
Bar wire holes are suitable for (1) #14-4 or up to (3) #14-10 aluminum or copper wire. Multiple wires in a single hole must be of the same size and material. Distance between mounting holes is 1-3/4". NOTE: Consult local code for correct application of ground bar kit for service entrance equipment. Kit contains one ground bar and two #10-32 x 5/8" self-threading screws. UL Listed. For easy access and pulling of wires through conduit run. For use with Schedule 40/80 non-metallic solvent weld fittings. Will not rust or corrode. UL Listed. For flexible conduit. Non-metallic/non-conductive, corrosion resistant plastic.
Square D PK23GTACP Ground Bar Kits Siemens EC38599 Type RX Conduit Hub 1 NM/SE CLAMP CONNECTOR
Used in load centers, CSED devices and NQOD and NF panel boards. Each terminal accepts (1) #14 - #4 copper wire or (1) #12 - #4 aluminum wire, (2) #14 - #12 copper wire or (2) #12 - #10 aluminum wire. NOTE - Consult local code for correct application of ground bar kit for service entrance equipment. ANSI Certified and UL Listed. For use on all Siemans and Murry single position meter sockets. Fits non metallic cable number 14/2 to number 6/3 AWG or number 3/10/3 AWG or flex cord .450 to .730 inches diameter. With a 1/2" knockout. In a dry location, use to connect nonmetallic sheathed cable to a steel outlet box or other metal enclosure. UL Lis
1-1/4 NM/SE CLAMP CONNECTOR Halex 96821 Rigid Reducing Conduit Washer Halex 93592 Ground Clamp
Fits non metallic cable number 6/3 to number 2/3 AWG flex cord .800 to 1.350 inches diameter or SE cable 3 conductor or 3 number 1/0 minimum; 3 conductor or 3 number 2/0 maximum. With 1/2" knockout. In a dry location, use to connect nonmetallic sheathed c Use to reduce the size of the conduit hole knockout opening in a steel outlet box or other metal enclosure. Must use one inside the enclosure opening and one on the outside. UL Listed, CSA Approved. Connects grounding wire to the grounding rod.
   
 
1 2 3 ... 20